Navigation

    The Onewheel Forum

    Onewheel Forum

    • Register
    • Login
    • Search
    • Categories
    • Recent
    • Popular
    • Users
    • Groups
    • Rules
    • Archive

    🚨 Please see top pinned post in general about the future of this forum 🚨

    Kush low as front footpad

    Mods & DIY
    6
    30
    9216
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • M
      MacIak DIY GT XR Plus last edited by

      20220205_184703.jpg

      Just an addition for the topic: Kush-lo+ pint sensor.
      Added diy CF plate as anti-ghosting and sturdy bottom plate, kush is kinda flexible;)

      Aka "Vommbat"

      NotSure 2 Replies Last reply Reply Quote 3
      • NotSure
        NotSure XR Pint @MacIak last edited by

        @maciak said in Kush low as front footpad:

        diy CF plate

        printed or purchased?

        M 1 Reply Last reply Reply Quote 1
        • M
          MacIak DIY GT XR Plus @NotSure last edited by

          @notsure
          Neither lol, hand laminated using the bottom of the pad for shaping since the front part curves up.

          3(or 4, dont remember) layers of unidirectional 340g/m2 fiber.

          Aka "Vommbat"

          1 Reply Last reply Reply Quote 2
          • M
            MacIak DIY GT XR Plus @Sirgu last edited by

            @sirgu really like this. Im curious what it looks like under that grip!

            Aka "Vommbat"

            Sirgu 1 Reply Last reply Reply Quote 1
            • NotSure
              NotSure XR Pint @MacIak last edited by

              @maciak said in Kush low as front footpad:

              Kush-lo+ pint sensor.

              i wonder if this could be done for the airpad? it already has a sturdy base plate. i never tried peeling off the gel tho. i'd love that. id buy it immediately.

              M 1 Reply Last reply Reply Quote 1
              • M
                MacIak DIY GT XR Plus @NotSure last edited by

                @notsure said in Kush low as front footpad:

                @maciak said in Kush low as front footpad:

                Kush-lo+ pint sensor.

                i wonder if this could be done for the airpad? it already has a sturdy base plate. i never tried peeling off the gel tho. i'd love that. id buy it immediately.

                Is the gel part not inside the pad?

                Aka "Vommbat"

                NotSure 1 Reply Last reply Reply Quote 1
                • NotSure
                  NotSure XR Pint @MacIak last edited by

                  @maciak said in Kush low as front footpad:

                  Is the gel part not inside the pad?

                  that whole yellow piece is the "gel". its just soft rubber. under that is an aluminum base plate that provides the rigidity.
                  6f4a74a8-aefc-4d9c-bede-e68362e820a8-image.png

                  M 1 Reply Last reply Reply Quote 1
                  • M
                    MacIak DIY GT XR Plus @NotSure last edited by

                    @notsure
                    I get it. Well, it depends. If that pad flexes enough so the toeside pressure deforms the heelside for instance, it could lead to undesired behaviour : such as heel-lift at standstill wont disengage the board.

                    Also i can think of slow recovery of the pad back into shape after compression. So the moment you lift your foot the pad stays in that shape a bit longer. This would certainly lead to ghosting.

                    I think you can determine by the feel of that pad if it has any characteristics i described above.

                    Aka "Vommbat"

                    NotSure 1 Reply Last reply Reply Quote 2
                    • NotSure
                      NotSure XR Pint @MacIak last edited by NotSure

                      @maciak said in Kush low as front footpad:

                      Also i can think of slow recovery of the pad back into shape after compression. So the moment you lift your foot the pad stays in that shape a bit longer. This would certainly lead to ghosting.

                      thats a good point. what if the sensors are applied to the aluminum instead of the pad and covered with a low friction film of some kind? maybe kapton or pfte tape? the rubber does compress easily but it does not travel with respect to the base.

                      M 1 Reply Last reply Reply Quote 1
                      • M
                        MacIak DIY GT XR Plus @NotSure last edited by

                        @notsure
                        Yes, a guy on the Onewheel subreddit is using it successfully like that. Here's a link to one of his posts:

                        link text

                        Aka "Vommbat"

                        1 Reply Last reply Reply Quote 2
                        • Sirgu
                          Sirgu XR @MacIak last edited by

                          @maciak Yea, the day I posted it I had no idea the PlatySense v4 design involves single pressure sensor. Which is bummer for me. I'm keen on heel-lift disengage. :/
                          For now there's bunch of FB short vids of how on point sensitive it turned out.
                          Recent YT video here:
                          https://www.youtube.com/watch?v=JmKEnJOfZJM&ab_channel=BartMiller

                          M 1 Reply Last reply Reply Quote 3
                          • M
                            MacIak DIY GT XR Plus @Sirgu last edited by MacIak

                            @sirgu
                            Oh dang! I watched that vid but missed the single sensor part coz i got pissed off by how he was slamming on the stock pad like an ape. This vid is very stupid tbh.
                            Edit: I dont like posi either tbh. The dual pad is about the only fail-safe we have and im no trickster.

                            Aka "Vommbat"

                            1 Reply Last reply Reply Quote 0
                            • First post
                              Last post