@s-leon You know, that almost looks like a OW track across that car hood!

@lia Ah so it would be like a future proof build if a 24s battery was to be used further down the line. Thanks!

I don't have any photos for my or my costume
I will try next year, but this semester has honestly been draining the life out of me, and I didn't get any time to prepare for halloween or even dress up sadly.

@reelwons Ouch that does sound like a bad pack. Lemur's suggestion is probably the best one as the replacement pack will still be good for a VESC build if you go down that route later.

It may be possible for it to be restored with replacement cells but you would need someone capable of dismantling the welds and then welding in new cells. Afterwards the board would recalibrating as disconnecting the battery from the BMS causes an error that disable the board till cleared.
https://www.fixmypev.com/diy/onewheel/gt/calibrate/
Just to re-iterate Lemur's point this only works on firmware versions prior to haptic buzz.

@lemur this is awesome! Keep up the good work!

Pin 1 : SW+ (power switch)
Pin 2 : NC (Not connected)
Pin 3 : W+ (Rear light White +)
Pin 4 : R+ (Rear light Red +)
Pin 5 : NC (Not connected)
Pin 6 : BMS RX (BMS communication receive)
Pin 7 : Batt - (Battery -)
Pin 8 : Batt + (Battery +)
Pin 9 : CHGR + (Charge detection)
Pin 10 : NC (Not connected)
Pin 11 : W- (Rear light White -)
Pin 12 : R- (Rear light Red -)
Pin 13 : NC (Not connected)
Pin 14 : BMS TX (BMS communication transmit)
Pin 15 : Batt - (Battery -)
Pin 16 : Batt + (Battery +)

7e4f317a-4114-4264-adeb-8464691582c8-image.png

Another pic for good measure :) This is from my Plus.
cab3026e-d878-47ba-be5f-10038bbd7500-image.png

@lemur I've given it some thought and I might take a swing at making an alternative daughterboard for the GT to accept the new Superflux V2 connector. Gonna be very DIY and hands on but a nice clean solution if I can pull it off.

Gotta finish a few other things up first. The new XR based controller housing for Fungineers is nearing completion so I should have some time after that to give it a swing.

@speedracer Swipe to the side after it finishes. It's not super obvious sadly.
Once you get through the many other pages and other videos you will see an option to not see it again.

@lemur This is exciting!

So I managed to become a beta tester for the haptic buzz for VESC.

It’s a trip hearing and feeling the motor buzz, but it only feels like if someone strapped a vibration motor to my board and kept spinning it

@OneDanGT @teddybeavis Yo, thanks for detailed insight! Also glad the update went without any glitches for you two. Any of you willing to do paved uphill test at modest speed? Might experience your Haptic Buzz properly for the first time.

@biell cheers… 👍 probably not going to update the board. However, let’s see what the feedback is when the XR update is available.

Doh, forgot to mention it was an XR…. 😊

@endlessme Hiya,

The link sadly doesn't grant access to see but from the description that's a 100ohm resistor.

You should be able to upload the pictures here by just dragging it into the compose section or clicking the "upload image" icon.
06308603-127c-41ee-aa50-adb64f53adf8-image.png

@lia I just changed out the two large caps that were rated for 63 v for 80v ones

@lemur Maybe use a variable resistor and just be careful not to crank it too much to feed the poor STM a big voltage? Then you can measure that and go for a set value :)

I think diagnostics tab in the app might give you the voltage it thinks it is so you can be a bit more scientific ^-^

Soooo turns out riding fenderless over a bunch of pine needles is far less than desirable. So much so, I broke and picked up a full fender. With a little modification it fits the FAF rails. Just have to get used to the noise again... I forgot how loud they are.

IMG_0578.jpeg IMG_0582.jpeg

In the app for my V1 battery percentage I got a huge negative number yesterday: " -25,136%"

IMG_5483.JPEG